Showing 4441–4464 of 6412 resultsSorted by popularity
Oil pump alignment kit for BMW N20 and N26 1.6L and 2.0L petrol engines, used to hold the balance shaft and chain sprocket during timing repair work.
Pneumatic CV boot tool for installing uni-fit CV joint boots, with air-controlled expanding fingers, 72-130psi working pressure and a 1/4in air inlet.
Timing tool kit for Citroen and Peugeot 1.0 and 1.2 VTi petrol engines, used to lock camshaft and crankshaft at TDC for accurate timing work.
Replacement 45 x 60mm rubber sanding drum with 80 grit abrasive, made for use with CT5911 drum sanders when worn drums need changing.
300mm diamond cutting disc with laser welded construction, made specifically for asphalt cutting during roadwork, repair cuts and groundwork preparation.
Hydraulic brake hose pinch clamp with one-handed snap action and 210 x 40 x 10mm dimensions for brake repairs, inspections and component replacement.
2 tonne low trolley jack with an aluminium body and 85-425mm lift range for access under lower vehicles during tyre changes, brake work and servicing.
Timing chain tool set for Ford 1.5L 3 cylinder EcoBoost petrol engines from 2018 onwards, covering engine codes YZJA, Y2DA, Y1DA and YZDA.
Rear camshaft pulley installer and remover kit for Ford and Mazda 2.5 and 3.0 V6 engines, used during water pump servicing and pulley refitting.
132mm brake spring installer for Mercedes rear disc parking brake spring clips, used for fitting and removing clips during brake servicing and repair work.
Connector removal tool for releasing VAG and Porsche push pull plugs without damaging clips, housings or wiring during vehicle servicing and electrical repairs.
3 ton hydraulic jack in a trolley format, with a 100mm minimum height and 535mm maximum lift for wheel changes, brake checks and servicing.
600mm stainless steel ruler and spirit level tool with metric and imperial markings, an anti-slip handle and two vials for measuring, trimming and levelling.
2-piece ignition coil puller set for Vauxhall and Opel vehicles, KM 6009 equivalent, for safer coil removal during servicing, fault finding and repair work.
8-piece 6in detail sanding swab set with double sided flexible abrasive heads in assorted grits for wet or dry sanding, rust removal and close detail work.
1.5 ton low profile car trolley jack with hydraulic lifting and a 70-610mm lift range for tyre changes, brake work and lower cars.
9/16in Land Rover prop shaft nut socket with 3/8in drive and 150mm length, made for reaching awkward fixings on Defender, Discovery and Range Rover P38 models.
Stretch belt tool for fitting A/C belts where no tensioner is fitted, covering N62 V8 applications from 2004-2006 and W17 diesel engines.
18+ ID check4in/100mm reciprocating saw scraper attachment, suited to removing tile adhesive, lifting flooring and tougher surface prep work.
8-piece spline bit set in M4-M16 sizes with 1/4in, 3/8in and 1/2in drive sockets, supplied on a rail for servicing, repairs and workshop maintenance.
HSS cobalt drill bit with a cone step design covering 4-30mm, made with 5% cobalt alloy for cutting and enlarging holes in thin metal up to 4mm thick.
Battery cable crimping tool in hardened steel for 6.2-11.6mm cable diameters, with a wide throat for terminal insertion on automotive and marine leads.
10-piece metric spanner set with a stubby design, 10-19mm sizes, open and ring ends, polished chrome finish and dipped handles for tighter spaces.
1/2in drive ratchet wrench with 90 tooth mechanism, quick release button and reversible cranked handle for garage, workshop and vehicle maintenance use.
Cookies on ToolBuyer
We use essential cookies to make the website work. With your permission, we also use analytics cookies to understand how it is used, and marketing cookies and similar tools from Google and Meta (Facebook and Instagram) to measure adverts and show adverts based on your visits and shopping activity. You can reject optional cookies or change your choices in Cookie settings. Cookie policy