Showing 4513–4536 of 6412 resultsSorted by popularity
48mm x 60m laminated waterproof gauge tape with brick and block markings for building profiles, helping keep bricklaying set out clear and consistent on site.
50L air compressor with a 2.4HP belt drive motor, 205L/min delivery, twin outlets and 10 bar maximum working pressure, plus wheels and a handle.
6in 150mm heavy duty steel spring clamp with hinged jaws, 80mm jaw capacity and rubber non-slip grip for quick holding on flat or uneven surfaces.
33m brick gauge tape for marking building profiles at 75mm, 150mm and 225mm. Laminated waterproof finish for clear, consistent brick and block course setting out.
3 tonne flat polyester webbing lifting sling for general load handling. Broad strap support helps move heavy items with less risk of marking surfaces.
5mm steel ground anchor for wall or floor fitting, supplied with M10 bolts for securing bikes, motorbikes, tools and other equipment to a solid surface.
8L car oil drain pan on wheels with a mobile tool caddy rated to 22.5kg, plus a splash guard to hold the drain plug during oil changes and servicing.
Block paving gap wedge with hardened steel wedge, 900mm long handle, hammer point and foot lug for lifting, adjusting and resetting paving blocks.
4 piece motorbike tyre lever set with 12in, 16in, 20in and 24in lengths for tyre removal and refitting in the workshop, garage or at home.
130mm internal profile clamp with steel zinc plated body, 40 x 40mm eye and T bolt thumb screw for box section, frame assembly and profile work.
Engine timing tool set for VAG EA839 2.9 and 3.0 TFSI petrol engines, used to hold camshafts in position during timing chain removal and installation.
Pack of 4 external brick line holder clips for 50mm x 50mm profiles. Fits Blakes, PT Profiles and Taylor Tools for brickwork setting out.
1m trailer breakaway cable with 6mm wire, an 8mm hook and 50mm ring, used to activate the brakes if a trailer or caravan detaches from the towing vehicle.
18+ ID checkPack of 10 replacement 18mm snap off blades in a plastic storage case for opening boxes, trimming materials and utility cutting, for customers aged 18 and over.
4-piece replacement setting screw set for one standard Blakes External Building Profile, complete with foot and zinc plated for site and outdoor use.
8L air powered automotive fluid extractor and ATF refill kit for transmission servicing, with a pressure gauge, safety shut-off and 13 one-touch adaptors.
Replacement setting device for Blakes building profiles, used for setting out and repositioning profiles on site. Handy as a spare when the original is missing or worn.
Injector seal puller for removing diesel fuel injector copper washers and seals, with a slim shaft, threaded conical tip and slide hammer action for stuck washers.
Traditional manure fork with a long ash wood handle for picking up and moving manure during farm, stable and equestrian maintenance work.
Timing locking tool kit for camshaft locking during timing belt changes on selected 16V and 20V twin cam petrol engines, including N7Q and N7U units.
Lightweight profile block dolly for bricklaying setups using 50mm x 50mm box section, with a 450mm x 450mm frame and 6mm tightening bracket.
18+ ID checkCompact folding utility knife with lock back action, quick change blade changes, 5 extra blades and a storage pouch for everyday cutting jobs.
16oz rubber mallet with a fibreglass handle for workshop, garage and fitting jobs where a softer striking face helps reduce surface marking.
Bricklaying profile clamp for full and double brickwork, holding 50.5mm to 60mm profiles steady on walls with a cavity width of up to 110mm.
Cookies on ToolBuyer
We use essential cookies to make the website work. With your permission, we also use analytics cookies to understand how it is used, and marketing cookies and similar tools from Google and Meta (Facebook and Instagram) to measure adverts and show adverts based on your visits and shopping activity. You can reject optional cookies or change your choices in Cookie settings. Cookie policy