Vehicle service & repair tools for mechanics and owners carrying out maintenance, component removal and repair work. Browse wheel nut sockets, air conditioning tools, alternator pulley kits and wheel repair products, choosing equipment by the job and the vehicle or component it is designed to fit.
Showing 1081–1104 of 1772 resultsSorted by popularity
3 ton hydraulic off road jack for 4×4 and high-clearance vehicles, with large non-pneumatic wheels, extension and steel skid plate for rough ground use.
10 ton hydraulic press for workshop use, with a floor-standing H-frame, 135mm stroke and 0-340mm work range for pressing, bending and straightening.
Hydraulic bush installer and extractor set with 18 ton force, 18-60mm coverage, short and long sleeves, and four spindles for bearing and seal work.
Spindle key with 12-24mm internal hex sizes for motorcycle front wheel and axle removal, helping hold the spindle steady while loosening or tightening the wheel nut.
Intermediate lever spring removal tool for BMW petrol VVT engines, used for removing and installing intermediate shaft control springs on selected N-series engines.
Deep 100mm intake manifold socket wrench with 3/8in drive and 8 point fitment for loosening and tightening recessed manifold screws on selected vehicles.
8-piece slide hammer set with M10 thread adapters, 200g hammer and 260mm shaft for removing threaded caps with a single access hole.
12-piece threaded cap puller kit with 700g slide hammer, 9 thread adaptors and M10/M14 connecting nuts for removing stubborn threaded caps.
10-piece slide hammer puller set with a 290mm rod, M12 connections and adaptor fittings for removing tight bearings, gears and shafts in garage or workshop use.
Universal press and pull sleeve kit for removing and fitting bushes, bearings and seals on HGVs, LGVs and tractors using a spindle or workshop press.
Steel inner driveshaft extractor fork with 85mm jaw and 380mm length for front wheel drive vehicles. Helps remove inner shafts with better leverage and less risk of damage.
Manual fuel siphon pump with a rubber ball hand pump, one 1100mm tube and one 380mm tube for transferring fuel, oil, water and antifreeze.
2-piece forked pry lever set for clutch, transmission and ball joint work, with two lengths to help with awkward access and stubborn parts.
17mm valve adjustment socket with 1/2in drive for Mercedes-Benz M100, 110, 114, 115, 123 and 130 engines during valve clearance servicing.
Specialist eccentric shaft pliers for aligning sliding blocks on selected BMW, Mini, Citroen and Peugeot engine applications during servicing and repair work.
Crankshaft turning and holding kit for BMW and Mini B37, B38, B47 and B48 engines, used to rotate the crankshaft and secure the flywheel during service work.
13mm top mount tool with 3/8in drive for VW, Audi, SEAT and Skoda VAG suspension strut nuts. Flexible design helps with awkward access during removal.
74.5mm 8-flute oil filter removal wrench with 1/2in drive for Fiat 500, Fiat Panda and Lancia Ypsilon 1.0 mild hybrids from 2020 onwards.
32mm 6-point fuel filter socket for Ford Transit Custom Mk8 2.0 TDCi 2016 onwards, with 1/2in drive for secure diesel filter removal during servicing.
AdBlue tank cap remover for Peugeot and Citroen PSA vehicles, used with a 3/8in drive or 17mm spanner for seized cap removal and refitting.
Lever tool for removing and fitting stubborn wheel bearing internal circlips, including clips without plier holes on selected Vauxhall, Opel, Ford, PSA, Fiat and VAG models.
5:1 Ford crankshaft torque multiplier set for pulley bolts on EcoBoost, Duratec, TDCi and EcoBlue engines, helping with the correct tightening sequence.
Mini N14 and N18 fuel line removal tool for Cooper S and JCW models, releasing the quick connect coupler on the low pressure line that supplies the high pressure fuel pump.
Radar sensor positioning tool for selected Volvo models, used during ADAS calibration to align the front radar sensor accurately with OEM 9997407 equivalent fitment.
Car repair tools and garage equipment for servicing cars, vans, motorcycles and trucks, arranged by the job. Lifting Gear holds trolley jacks, axle stands and bottle jacks, Workshop Equipment covers hydraulic presses, air compressors and creepers, and Wheels & Tyres has tyre levers, tyre changers and locking wheel nut removers. Brake Servicing brings brake bleeding kits, caliper rewind tools and pipe flaring tools, while Timing Tools lists engine timing kits by engine code.
Special Application Tools gathers mechanic tools for suspension, steering, cooling and diesel injection work, and Transmission Servicing has clutch alignment tools, transmission jacks and gear pullers. The remaining sections cover grease guns and oil filter wrenches, jerry cans and siphon pumps, jump leads and battery testers, dent pullers and trim removal tools, exhaust cutters, electric winches and chain blocks, and magnetic pick up tools and inspection mirrors.
Cookies on ToolBuyer
We use essential cookies to make the website work. With your permission, we also use analytics cookies to understand how it is used, and marketing cookies and similar tools from Google and Meta (Facebook and Instagram) to measure adverts and show adverts based on your visits and shopping activity. You can reject optional cookies or change your choices in Cookie settings. Cookie policy