Transmission servicing tools for mechanics working on bearings and gears, including puller sets and press-and-pull kits. Compare tool formats and stated component applications for the work involved. The supplied list also contains airbag and ball joint tools, so those category assignments need review.
Showing 49–72 of 96 resultsSorted by popularity
Gearbox seal tool set for Ford DPS6 and 6DCT250 dual clutch gearboxes, covering input shaft, differential and drive shaft seal removal and fitting.
Locating pin puller for ZF12S and ZF16S gearbox cover removal, made from 40Cr steel with a 140mm length and 34mm outer diameter.
30mm suspension strut support for hydraulic vertical transmission jacks and gearbox stands, helping hold struts steady during repair and maintenance work.
36mm slim fan hub wrench for Ford, Opel and GM visco clutch work. 270mm length with PVC dipped handle for easier access in tighter engine bays.
Gearbox tool set for Audi A4, A5 and Q5 0B2 and 0B5 transmissions, including side shaft counter holder and sensor module tool for gearbox work.
Universal press and pull sleeve kit for removing and fitting bushes, bearings and seals on HGVs, LGVs and tractors using a spindle or workshop press.
2-piece forked pry lever set for clutch, transmission and ball joint work, with two lengths to help with awkward access and stubborn parts.
Under-vehicle engine support beam rated up to 400kg, with 645-965mm length adjustment and support hooks for clutch, gearbox and timing belt work.
Clutch reset tool for Ford DPS6 DCT gearboxes, used to re-spring and reset a removed dual clutch assembly before refitting on selected Ford models.
Ford AC compressor clutch pulley tool with 3/8in drive for Fiesta, B-Max and C-Max models from 2008 to 2015, holding the pulley still while the fixing bolt is removed.
3/8in drive Ford compressor clutch pulley retaining tool for selected models from 2010 onwards, used to hold the A/C pulley steady during removal work.
3/8in drive A/C compressor clutch pulley retaining tool for Ford 2012-on models, used to hold the pulley still during removal of the fixing bolt.
3/8in drive Ford AC compressor clutch retaining tool for selected models, used to hold the pulley during A/C pump or pulley replacement work.
1000mm engine support beam rated up to 400kg for holding engines or transmissions during clutch, gearbox and cam belt work on transverse vehicles.
Small bearing puller kit with 5.5mm, 6.0mm and 8.0mm inserts, a 20-90mm adjustment range and a forcing screw for recessed bearing removal.
26pc universal bearing press and pull sleeve kit for fitting and removing bushes, bearings and seals in garage, workshop and repair work.
7-piece drive shaft puller service socket set with sizes from M16 to M30 for selected BMW, VW, VAG, Porsche Cayenne and Subaru servicing work.
Track rod end remover for 28-35mm axial inner tie rod ball joints, with 400mm length, 27mm hex and 1/2in drive for steering repair work.
Ball joint tool kit for E36 suspension arms, with a press frame, spindle and sleeves for installing and removing supporting joints and compatible bushes.
Front suspension bush tool for VW Polo 2002-on VAG models, made for accurate removal and replacement during suspension repair and maintenance work.
DSG clutch installer remover kit for Audi and VW VAG 7-speed dry double clutch gearboxes, used for clutch and gearbox removal and refitting work.
Large C-frame ball joint tool for press-fit joints on cars and light trucks, also suitable for tie rod ends and for removing and fitting universal joints.
Heavy duty hydraulic bearing puller set for removing seized gears, bearings and sprockets during vehicle, workshop and machinery repairs.
Air powered CV boot expander for 20-110mm CV joints, also fitting flexible steering boots, with a control valve and 1/4in BSP rear air inlet.
Clutch alignment tool kits in 6, 10, 17 and 38 piece sets, including SAC self adjusting clutch tool kits for BMW and an HGV single and double disc kit. Dual clutch gearbox work is covered by Ford DPS6 reset and seal tools and a 7 speed DSG installer kit for VAG. Transmission jacks come in 500kg vertical, 1000kg low profile and 1 ton gearbox jack versions, with engine and gearbox support beams.
Gear puller and bearing puller sets range from 2 and 3 leg reversible pullers to 10, 30 and 50 ton hydraulic bearing puller kits, with bearing separator sets, a press and pull sleeve kit and a bush and bearing driver set. Ball joint separator sets, track rod end tool options and a tie rod puller handle steering joints, and a pneumatic CV boot tool expands boots for fitting. Check the jaw reach against the part before ordering.
Cookies on ToolBuyer
We use essential cookies to make the website work. With your permission, we also use analytics cookies to understand how it is used, and marketing cookies and similar tools from Google and Meta (Facebook and Instagram) to measure adverts and show adverts based on your visits and shopping activity. You can reject optional cookies or change your choices in Cookie settings. Cookie policy